User Tools

Site Tools


howto:modp3params

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
howto:modp3params [2018/06/12 02:26]
digdat0 [Important Parameter Descriptions]
howto:modp3params [2018/06/12 02:26] (current)
digdat0 [Important Parameter Descriptions]
Line 113: Line 113:
  
 ^ Parameter Name ^ Description^ ^ Parameter Name ^ Description^
-g_config.advanced_function.height_limit_enabled_0|Removes height limit| +^ advanced_function.height_limit_enabled_0|Removes height limit| 
-g_config.control.horiz_vel_atti_range_0|GPS Tilt angle makes faster| +^ control.horiz_vel_atti_range_0|GPS Tilt angle makes faster| 
-g_config.control.atti_range_0|ATTI Max tilt angle| +^ control.atti_range_0|ATTI Max tilt angle| 
-g_config.control.atti_limit_0 | ATTI tilt angle +^ control.atti_limit_0 | ATTI tilt angle| 
-g_config.control.vert_up_vel_0|Ascent Velocity Rate (Up)| +^ control.vert_up_vel_0|Ascent Velocity Rate (Up)| 
-g_config.control.vert_down_vel_0|Descent Velocity Rate (Down)| +^ control.vert_down_vel_0|Descent Velocity Rate (Down)| 
-g_config.airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement +^ airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement| 
-g_config.airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ| +^ airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ| 
-g_config.airport_limit_cfg.cfg_limit_data_0 | NFZ map data value +^ airport_limit_cfg.cfg_limit_data_0 | NFZ map data value| 
-g_config.airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone) +^ airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone)| 
-g_config.flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP| +^ flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP| 
-g_config.voltage.level_1_protect_type_0|Battery level 1 function (warn, led)| +^ voltage.level_1_protect_type_0|Battery level 1 function (warn, led)| 
-g_config.voltage.level_2_protect_type_0|Battery level 1 function (warn, led, land)| +^ voltage.level_2_protect_type_0|Battery level 1 function (warn, led, land)| 
-g_config.voltage2.level_1_voltage_0|Battery level 1 %| +^ voltage2.level_1_voltage_0|Battery level 1 %| 
-g_config.voltage2.level_1_function_0|Battery level 1 function (warn, land)| +^ voltage2.level_1_function_0|Battery level 1 function (warn, land)| 
-g_config.voltage2.level_2_voltage_0|Battery level 2 %| +^ voltage2.level_2_voltage_0|Battery level 2 %| 
-g_config.voltage2.level_2_function_0|Battery level 1 function (warn, land)| +^ voltage2.level_2_function_0|Battery level 1 function (warn, land)| 
-g_config.voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| +^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| 
-g_config.voltage2.level2_smart_battert_land_0|SmartRTH battery landing %|+^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %|
 ====== Parameter Values to Change ====== ====== Parameter Values to Change ======
 I removed the g_config from the prefix to make the table fit better :) I removed the g_config from the prefix to make the table fit better :)
howto/modp3params.txt · Last modified: 2018/06/12 02:26 by digdat0